Protech ZOOM 425 ccpm Specifications Page 65
- Page / 240
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Kyosho Blade Balance
7.2.3. Paddle pitch gauge (optional)
This is very handy for ensuring your paddles are completely flat relative to each other. For non-
micro helicopters, the KSJ-624 paddle gauge works well.
KSJ paddle pitch gauge set
7.2.4. Prop balancer (optional)
In order to balance the rotor head, you need a prop balancer. The Du-bro "Tru-spin prop balan-
cer" works well because you can hang the rotor head over the edge of a table when balancing
he rotor head.
7.2.5. Tachometer
There are about three tachometers in wide use for helicopters.
The first is the Anderson Hobby tachometer. This is fairly cheap about $35) and works well on
the ECO/Logo, but it does NOT work on micro helis such as the Piccolo CP! It also drains bat-
teries quickly even when not turned on, so I recommend removing the battery when not in use.
The second is the X-cell optical tachometer. This is expensive(about $150) but works with al-
most any helicopter. It only reads to 1990 rpm, so it may not be suitable for micro helicopters
which typically need 2000+ rpm of headspeed.
The third is the Tera tachometer distributed by Thunder Tiger. This is a very nice digital tacho-
meter specifically for helicopters which will clip onto the tail boom for hands-free measuring of
Support Equipment
52
- Guide v17 1
- Toshiyasu Morita 2
- Mark Pearson 2
- Table of Contents 4
- List of Tables 12
- 1.2. Repairs are expensive 14
- 2.5. Summary of skills 15
- 3.2. Clones 18
- 3.2.1. Design problems 19
- 3.4.1. Lite Machines Corona 21
- 3.4.4. Ikarus ECO Lite 22
- 3.4.5. Ikarus ECO 8 22
- 3.4.6. Ikarus ECO 16 22
- 3.4.10. JR Voyager E 23
- 3.4.12. Mikado Logo 10 24
- 3.4.13. Mikado Logo 20 24
- 3.4.14. MS Composit Hornet FP 24
- 3.4.15. MS Composit Hornet CP 25
- 3.4.16. MS Composit Hornet II 25
- 3.4.17. Maxir SE 25
- 3.4.19. Quick Quick EP 10 26
- 3.4.20. Quick Quick EP 16 26
- 3.4.22. Align T-Rex 450X 27
- 3.4.24. ARK X-400 27
- 4.1. Beginner configurations 30
- 4.2.2. T-Rex 450XL 32
- 4.2.3. Zoom 400 32
- 4.2.4. Logo 10 - brushless 32
- 4.2.5. ECO 8 - brushed 33
- 4.2.6. ECO 8 - brushless 33
- 5.1. Corona upgrade paths 34
- 5.2. Piccolo upgrade paths 35
- 6.1. Control system 37
- 6.2. Servos 41
- 6.2.2. Tail (rudder) servo 42
- 6.3.1. Batteries 43
- 6.3.2. Battery connectors 45
- General recommendation 47
- 6.3.4. Wire 48
- 6.4. Motors and related items 49
- 6.4.1.2. FP Piccolo motors 50
- 6.4.1.6. Hornet CP motors 51
- 6.4.1.7. Maxir SE motors 51
- 6.4.1.8. Zoom 400 motors 51
- 6.4.1.10. ARK X-400 motors 52
- 6.4.1.11. Voyager E motors 52
- 6.4.1.12. Robbe Eolo motors 52
- 6.4.1.13. ECO 8 motors 52
- 6.4.1.14. ECO 16 motors 54
- 6.4.1.15. Viper 70 motors 54
- 6.4.1.16. Logo 10 motors 54
- 6.4.1.17. Logo 14 motors 55
- 6.4.1.18. Logo 20 motors 55
- 6.4.1.19. Quick EP 10 motors 55
- 6.4.1.21. Summary 56
- 6.4.2. Pinion 57
- 6.4.3. Motor connectors 57
- 6.4.4. Main motor ESC 57
- 6.4.5. Tail motor ESC 60
- 6.5. Other 61
- Helicopter Parts Selection 62
- 7.2. Helicopter tools 64
- 7.2.5. Tachometer 65
- 7.3. Adhesives 66
- 7.4. Charging equipment 67
- 7.4.3. Power supplies 69
- 7.5. Electronic instruments 71
- 7.5.2. Wattmeter 72
- Chapter 8. Simulators 73
- 8.3. Easyfly 75
- 8.4. Aerofly Professional 75
- Simulators 77
- 8.9. ClearView 81
- 8.10. PreFlight 81
- 8.11. PhoenixRC 82
- 8.13. Summary 83
- 8.14. Simulator practice 84
- Chapter 9. Transmitters 85
- 9.3. Transmitter tray 88
- 9.5. Transmitter manuals 89
- 10.1.1. Building 90
- 10.1.2. Threadlock 90
- 10.1.3. Gear lubrication 90
- 10.1.4. Frame assembly 90
- 10.1.5. Stripped threads 90
- 10.1.6. Breaking-in motors 91
- 10.1.7. Carbon dust 91
- 10.1.8. Capacitors 91
- 10.1.9. Motor diode 92
- 10.1.10. Ball links 92
- 10.1.11. Motor shaft 92
- 10.1.13. Canopy painting 93
- 10.1.14. Tail servo 93
- 10.1.15. Mounting component 93
- 10.1.16. Ball in swashplate 93
- Pro) only 95
- Making CA joints 96
- 11.1. Channel assignments 102
- 11.2. Component placement 104
- 11.3. Wire routing 105
- 11.4. Soldering technique 105
- 13.1. Center of gravity setup 109
- 13.2. Swashplate setup 109
- 13.2.2.3. Swashplate leveling 111
- 13.2.3.1. Normal mode setup 111
- 13.2.4.7. Check for binding 114
- 13.2.5.4. Check for binding 114
- 13.4. Main motor setup 117
- 13.5. Tail rotor setup 122
- 13.5.4.1. GY240 setup 123
- 13.5.4.2. GY401 setup 124
- 13.5.4.4. Yaw-rate gyro setup 126
- 13.5.5.1. GY240 setup 127
- 13.5.5.2. Yaw-Rate Gyro setup 128
- 14.5. Liability insurance 133
- 15.1. The skills required 134
- 15.2.3. Use white blades 135
- 17.3. Safety notes 139
- Chapter 18. Tail-In Hovering 140
- 20.1. Introduction 145
- 20.2. Inverted T 145
- 20.3. 90 degree yaw 145
- 20.4. 180 degree yaw 145
- 21.1. Using idle-up mode 147
- 21.3. Banked forward turns 147
- 21.4. Backwards flight 148
- 21.5. Banked backwards turns 148
- 22.1. Figure eights 150
- 23.1. Single pirouette 151
- 24.4. Add flybar weights 153
- 26.1. Vibration problems 155
- 26.2. Tail control problems 157
- 26.3. Throttle/ESC problems 161
- 26.4. Swashplate problems 162
- 26.5. Glitching 162
- 26.6. Other problems 163
- Mikado Logo 10 165
- Ikarus ECO 8/16 165
- Align T-rex 450X/450XL 167
- ARK X-400 167
- Motor vendors 167
- ESC vendors 168
- Servo vendors 168
- BEC manufacturers 169
- Main rotor blades 169
- Carbon fiber tubes and rods 169
- Other suppliers 169
- Hobby associations 170
- Useful webpages and forums 170
- Aerobatics 170
- Magazines 171
- Helicopter theory 171
- 28.1. General questions 172
- 28.2. Transmitters 173
- 28.4. Gyros 177
- 28.5. Helicopter setup 177
- Chapter 29. Helicopter Myths 178
- 30.1. How helicopters work 179
- 30.1.2.1. Throttle stick 180
- 30.1.2.2. Rudder stick 180
- 30.1.3.3. non-CCPM 181
- 30.1.5. The rotorhead 184
- 30.1.7. How gyros work 185
- 30.1.8.1. GY401 setup 188
- 30.1.8.2. GY240 setup 191
- 30.1.10. How ESCs work 192
- 30.1.10.3. Governor mode 193
- 30.1.10.4. Timing Advance 193
- 30.1.11. How batteries work 194
- 30.1.12. How motors work 194
- 30.1.12.1. Brushed motors 195
- 30.1.12.2. Brushless motors 197
- 30.1.12.3. Coreless motors 198
- 30.2. Motor selection guide 199
- 30.2.1.3. Motor efficiency 200
- 30.2.1.4. Motor rated RPM 200
- 30.2.2.1. Motor size 200
- 30.2.2.2. Motor weight 200
- 30.2.2.5. Cooling options 201
- Table 30.5. Heatsinks 201
- 30.2.3. Other characteristics 202
- 30.3. Motor selection table 203
- 30.4. Pinion selection guide 212
- 30.4.3. Shaft sizes 213
- 30.4.4. Pinion notes 213
- 30.5. Pinion selection tables 214
- 30.6. Servo selection guide 217
- 30.6.2.1. Size 218
- 30.6.2.2. Mounting lugs 218
- 30.6.2.3. Servo weight 218
- 30.6.2.4. Speed and Torque 218
- 30.6.2.5. Gear type 218
- 30.8. Battery info 220
- 30.11. Useful equations 225
- Glossary 227
Related products and manuals for Toys & accessories Protech ZOOM 425 ccpm
(20 pages)© 2020, manymanuals.com. All rights reserved. | 0.599 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals